Effect of PyC interface phase on the cyclic ablation resistance and flexural properties of two-dimensional Cf/HfC composites

Composites based on hafnium carbide and reinforced with continuous naked carbon fiber with and without PyC interface were prepared at low temperature by precursor infiltration and pyrolysis and chemical vapor deposition method. The microstructure, mechanical property, cyclic ablation and fiber bundle push-in tests of the composites were investigated. The results show that after three times ablation cycles, the bending strength of samples without PyC interface decreased by 63.6 %; the bending strength of samples with PyC interface only decreased by 37.8 %. The force displacement curve of the samples with PyC interface presented a well pseudoplastic deformation state. The mechanical behavior difference of two kinds of composites was due to crucial function of PyC interface phase including protection of fiber and weakening of fiber/matrix interface.     

Dense and core-rim structured B4C-TiB2 ceramics with Mo-Co-WC additive

B₄C-TiB₂ ceramics (TiB₂ ranging 5~70 vol%) with Mo-Co-WC as the sintering additive were prepared by spark plasma sintering. In comparison with B₄C-TiB₂ without additive, the enhanced densification was evident in the sintered specimen with Mo-Co-WC additive. Core-rim structured grain was observed around TiB₂ grains. The interface of the rim between TiB₂ and B₄C phases demonstrated different feature: the inner borderline of the rim exhibited a smooth feature, whereas a sharp curved grain boundary was observed between the rim and the B₄C grain. The formation mechanism is discussed: the epitaxial growth of (Ti,Mo,W)B₂ rim around the TiB₂ core may occur as a result of the solid solution and dissolution-precipitation between TiB₂ phase and the sintering additive. It was revealed that the fracture toughness increased as the content of TiB₂ content increased, alongside the decreased hardness. B₄C-30 vol% TiB₂ specimen demonstrated the optimal combination of mechanical properties, reaching Vickers hardness of 24.3 GPa and fracture toughness of 3.33 MPa·m^1/2.     

Effect of MoS2/PTFE coatings on performance of Si3N4/TiC ceramics in dry sliding against WC/Co

To enhance the tribological performance of Si₃N₄/TiC ceramics, MoS₂/PTFE composite coatings were deposited on the ceramic substrate through spraying method. The micrographs and basic properties of the MoS₂/PTFE coated samples were investigated. Dry sliding friction experiments against WC/Co ball were performed with the coated ceramics and traditional ones. These results showed that the composite coatings could significantly reduce the friction coefficient of ceramics, and protect the substrate from adhesion wear. The primary tribological mechanisms of the coated ceramics were abrasive wear, coating spalling and delamination, and the tribological property was transited from slight wear to serious wear with the increase of load because of the lower surface hardness and shear strength. The possible mechanisms for the effects of MoS₂/PTFE composite coatings on the friction performance of ceramics were discussed.     

Chromium-promoted preparation of forsterite refractory materials from ferronickel slag by microwave sintering

The chromium-promoted preparation of forsterite refractory materials from ferronickel slag was investigated by microwave sintering of the slag with the additions of sintered magnesia and 0–10 wt% chromium oxide (Cr₂O₃). The thermodynamic calculations revealed that the addition of Cr₂O₃ can promote the formations of spinel and liquid phase and maintain high content of forsterite below 1500 °C. The experimental results showed that there existed a stronger promoting effect of Cr₂O₃ additive on the properties of refractory materials in the microwave field than that in conventional sintering. It was attributed to the preferential formation and growth of spinel with stronger microwave absorption than other phases (e.g., enstatite), the existence of more forsterite, and the enhanced densification in association with the presence of more liquid phase at the same temperature. By microwave sintering of the mixture of ferronickel slag, 25 wt% sintered magnesia, and 4 wt% Cr₂O₃ at 1350 °C for 20 min, a superior refractory material with refractoriness of 1801 °C, thermal shock resistance of 6 times, bulk density of 2.97 g/cm³, apparent porosity of 1.4%, and compressive strength of 197 MPa was obtained. Compared with that prepared by conventional sintering at 1350 °C for 2 h, the refractoriness and thermal shock resistance were increased by 175 °C and 100%, respectively. The present study provided a novel method for preparing high-quality refractory materials from ferronickel slag and relevant industrial wastes.     

Influence of surfactants on rheological behaviors of polyacrylonitrile/dimethyl sulfoxide/silicon blending polymer solutions

KH550, KH560, CTAB, and F127 were adopted to modify silicon (Si) to improve the dispersity and stability of Si in the polyacrylonitrile/dimethyl sulfoxide (PAN/DMSO) polymer solutions. The influence of surfactants on rheological behaviors of PAN/DMSO/Si blending polymer solutions was investigated by an advanced solution and melt rotation rheometer. The homogeneity and stability were also studied. The results showed that the surfactants could change the viscosity dependence of blending polymer solutions on shear rate, temperature and storage time by increase the steric hindrance of Si. Among the four solutions, PAN/DMSO/Si blending polymer solution with F127 exhibited the lowest viscosity, activation energy and the smallest structural viscosity index and exhibited the trend close to the Newtonian fluids. Moreover, PAN/DMSO/Si blending polymer solution with F127 exhibited the best dispersity and stability, indicating its best physical properties and machinability.     

Influence of Sr ions on the structure and dielectric properties of Cu/Nb Co-doped BaTiO3 ceramics

Sr-modified Cu/Nb co-doped BaTiO₃ ceramics were prepared using solid-state reactions and the structures and dielectric properties were studied. All the samples had single-phase perovskite structures with no detectable secondary phases. In the low-temperature range, the dielectric constant decreased as the Sr content increased in the high- and low-frequency ranges. Two dielectric constant plateaus accompanied by dielectric relaxation peaks were present in the loss curves, and the relaxation process deviated from the Arrhenius law at low temperatures. The dielectric constants of different plateaus were related to inhomogeneous structures such as grain interiors and grain boundaries. The polarization strength of the grain boundaries in the low-frequency range increased with the temperature and that of the grain interiors demonstrated paraelectric behaviour in high-temperature ranges. An analysis of the electric modulus spectra indicated a close relationship between the relaxation process and resistivity of the grains for high-frequency relaxation. The impedance spectra at high temperatures consist of three electrical responses, corresponding to the effects of grains, grain boundaries, and electrodes. The dielectric relaxation appeared in high temperature range was related to the electrical properties of the grain boundaries.     

Piezoelectricity of the Transmembrane Protein ba3 Cytochrome c Oxidase

Controlling the electromechanical response of piezoelectric biological structures including tissues, peptides, and amino acids provides new applications for biocompatible, sustainable materials in electronics and medicine. Here, the piezoelectric effect is revealed in another class of biological materials, with robust longitudinal and shear piezoelectricity measured in single crystals of the transmembrane protein ba₃ cytochrome c oxidase from Thermus thermophilus. The experimental findings from piezoresponse force microscopy are substantiated using a range of control measurements and molecular models. The observed longitudinal and shear piezoelectric responses of ≈ 2 and 8 pm V⁻¹, respectively, are comparable to or exceed the performance of commonly used inorganic piezoelectric materials including quartz, aluminum nitride, and zinc oxide. This suggests that transmembrane proteins may provide, in addition to physiological energy transduction, technologically useful piezoelectric material derived entirely from nature. Membrane proteins could extend the range of rationally designed biopiezoelectric materials far beyond the minimalistic peptide motifs currently used in miniaturized energy harvesters, and the finding of robust piezoelectric response in a transmembrane protein also raises fundamental questions regarding the molecular evolution, activation, and role of regulatory proteins in the cellular nanomachinery, indicating that piezoelectricity might be important for fundamental physiological processes.     

Preconditioned method for the nonlinear complex Ginzburg–Landau equations

Wireless Networks - In this work, we give an effective preconditioned numerical method to solve the discretized linear system, which is obtained from the space fractional complex...     

GM-CSF及CBS在肝损伤中的研究进展

肝损伤(liver injury)是指基因遗传或外部原因诱发的肝脏功能异常性疾病.临床表现为食欲不振、乏力、恶心、黄疸、疲乏等,严重者将出现肝功能衰竭,致死风险极高.在交通肇事、暴力犯罪及意外事件中,肝由于体积大、位置固定、质地脆弱、血运丰富等原因,往往是最容易发生损伤的器官之一,肝损伤后的死亡率可高达10.5％～25％[1].随着时间的变化,肝损伤的程度、病理改变、GM-CSF等相关细胞因子及CBS等相关酶的表达水平也会进一步变化.肝损伤后,由于肝内部环境稳态的破坏,器官的状态、结构、各种蛋白的转录水平、蛋白及细胞因子的表达变化水平也会发生一定程度的改变.因此定性定量地分析这些变化,找到时间相关性强的特异性指标,对于指导法医学的实践具有重要的作用.因此在法医学鉴定中,通过肝脏损伤及病变程度的改变,明确肝损伤病变与死亡时间的关系有利于判断事件或案件性质,并有助于进一步对责任方的认定.